Question: How To Check Engine Light Codes?

How can I check my check engine light code without a scanner?

Using an odometer

Making use of the odometer is another way to retrieve the OBD2 codes. The user is required to depress the vehicle’s odometer. (The “reset” and “trip” buttons must be reset as well.) Simultaneously, the ignition key of the vehicle must be turned on and off.

Can I check my own check engine light?

You can. All that you need to check your own light is an OBD-II reader, which can pull codes that help you find out what’s wrong with your car. If you don’t have a code reader, keep reading to learn the most common causes, and then bring your car to your local AutoZone to find out why your Check Engine Light is on.

Does car have to be running to check codes?

Always turn the ignition on or have the car running according to the instructions in the manual. Failure to do this might corrupt the scanning software. It’s also very important that you drive around with the manual for the specific scanner model that you’re using.

You might be interested:  Readers ask: What Engine Lights Mean?

How can I check my car code?

To read the codes, you will have to plug a scan tool or code reader into the 16-pin OBD II diagnostic connector, which is usually located under the dash near the steering column. The tool will then display the code or codes that have turned on the Check Engine Light. To read codes, you need the proper scan tool.

What is the most common reason for check engine light?

Replacing a faulty oxygen sensor — a sensor used to optimize a vehicle’s fuel-to-air mixture to increase gas mileage and reduce emissions — is the most common cause for a check engine light.

Can low oil cause the check engine light to come on?

Low oil pressure is a common cause of a check engine light turning on, and it can seriously interfere with your car’s performance. Usually, if this is the case, your oil light will also appear. In any case, low enough oil pressure will disable your vehicle, so get this repaired immediately.

Where can I get my check engine light read for free?

At a local auto parts store

  1. Advance Auto Parts.
  2. AutoZone.
  3. Napa Auto Parts.
  4. O’Reilly Auto Parts.
  5. Pep Boys Auto Parts.

Where can I read car codes for free?

Free Code Reading

If you have a problem with your car and you don’t know what it is, most auto part stores (such as AutoZone, Pep Boys and Advance Auto Parts) will provide a free diagnostic code reading. It is also called an OBD reading.

Where can I get my check engine light checked?

Solving check engine light problems

  • Take your car to a mechanic and pay a diagnostic fee. Often, the fee is waived if you agree to have the necessary service performed at that garage.
  • Bring your car to an auto parts store and have the code read for free.
  • Buy an inexpensive scanner and read the code yourself.
You might be interested:  Quick Answer: How To Clean An Engine Block For Rebuild?

How do you tell if OBD codes have been cleared?

If the vehicle does not support the above datapoints you can use the smog check feature to check for indications of codes being recently cleared. When codes are cleared all vehicle emissions tests are reset and will display a status of ‘not complete’.

Can AutoZone check codes?

Many drivers don’t realize that AutoZone, the nation’s largest auto parts chain, will do the following services free of charge: Read the codes on your check engine light. Test your battery’s voltage.

Will check engine light reset itself?

Your vehicle’s check engine light will will reset by itself once the issue or problem has been repaired; this is true for most models. If you are certain that you have resolved the issue that caused your check engine light to come on in the first place, then the light should reset itself after at least 20 cycles.

How many miles do you have to drive to clear a check engine light?

To make sure the check engine light does not reappear, it’s recommended that you drive your car 30 to 100 miles. This enables the vehicle’s “Drive Cycle” to reset, as the various sensors need time to recalibrate.

Leave a Reply

Your email address will not be published. Required fields are marked *